Optional System Accessories

BACK BY POPULAR DEMAND!!!
The Spline Dovetail Jig is used with the SmartFence and IPM Fence to produce incredible Spline Joints. What's awesome about this jig is that it locks into the patented dovetail slot on SmartFence and IPM Fence - keeping the jig running true all the time. Made from MDF, this jig is proven. Holds your mitered box at 45 degrees to the table for cutting splines. With the Spline Dovetail Jig you can also make double dovetail splines as well as double box joint splines for any of your box projects. Can also be used on your table saw for adding decorative corners. Includes a 1 hour instructional DVD that will show you everything from Setup to achieving Exotic Decorative Spline Joints.    

The Combination Featherboard and Stock Pusher locks into the extruded dovetail on SmartFence. Holds the workpiece firmly down on the table for consistent cuts. Prevents kickback and keeps fingers safely away from the cutting tool. Reversible feathers for shaper or bandsaw.

Designed for 24", 27" and 32" router table tops. Holds the workpiece against both the infeed and outfeed faces of the fence for consistent cuts. Prevents kickback and keeps fingers safely away from the cutting tool. Feathers can be reversed for shaper or bandsaw use. Runner is an aluminum extrusion which provides more rigidity. This is the same extrusion that is used for the SawTrain Featherboard. Fastens to the table using clamps that pinch the sides of router table. Available for Standard Melamine Tops and for SOLID Phenolic.

Before the introduction of the Jumbo Face Plate, it was difficult to hold wide boards on end on top of a router table. The only way was to clamp a wider board to the standard Vertical Push Fixture, then you could clamp your board to the auxiliary piece. The Jumbo Face Plate’s 12” x 6-1/2” design allows you to handle larger stock accurately and easily.
VPF-JP   $20.95   ON SALE $16.99
BUY

Coping is making a profile cut across the end of a narrow board.This type of cut would be difficult to keep square to the fence by hand. Examples of coping are coping rail ends, slotting, tenoning, rabbeting, dadoing and glue joints such as drawer and lock miter. Our new Coping Kit will make these operations more precise, safer and much easier. It is used on the VPF-2 and includes three double-ended polyethylene blocks ready for profiling and a Plexiglass hold down shield. The blocks are machined and pre-drilled to attach to the VPF-2 faceplate when it is positioned for coping operations. After establishing the correct height of your bit, one end of a block is cut to that profile. It then becomes your backer to prevent tear out during use and then serves as a quick & perfect gauge block for future setups. The Hold Down Shield holds the stock to the table during coping operations and also serves as a bit guard when mounted onto SmartFence as shown below.
VPF-COPE   $29.95   ON SALE $22.99
BUY

Jointech’s Fence Raiser makes vertical panel raising safer and easier. It adapts quickly to SmartFence (24" & 32") to support large panels for all vertical panel raising operations. Includes support hardware for T-slots on top of SmartFence.
SF-P24 (for SF-24)    $19.95   ON SALE $14.99   BUY
SF-P32 (for SF-32)   $21.95   ON SALE $17.99   BUY

Kit includes a case-hardened twin drilling guide for both 3/8” and 5/8” hinges, a 6” long, 1/8” diameter HSS drill bit, one 5” length of brass rod for the hinge pins (JHK-ROD), a hardwood blank for making a pair of hinges and a complete illustrated instruction manual. This is the only drill guide which is hardened, plus, it incorporates precision backstops to guarantee perfectly drilled hinges every time. The only thing you will need is a bull nose router bit (shown below) to complete your first pair of wooden hinges. Be sure to order extra brass rod & Bull Nose Router bits!
JHK-1   $39.95   ON SALE $32.99   BUY

Extra Brass Rod

Hinge Making Kit is hard anodized so that it can be re-used repeatedly. For every hinge made, you will need to insert a piece of brass rod as the hinge pin. Extra rod is available in packs of four, one foot lengths. JHK-ROD    $3.99    $2.99 BUY

Jointech’s 2.5” Clamp comes in handy when cutting small stock using the Vertical Push Fixture. When workpieces are too narrow or too short, it is harder to grip the piece during the cutting process. This can create results that are less than perfect. The Hold Down Clamp uses a T-bolt that engages into the extruded T-slot on Vertical Push Fixture face plate.
The Hold Down Clamp can also be used with the Hinge Making Kit to hold small wooden hinge blanks while drilling for the brass hinge pin.
JHDC-2   $6.95   ON SALE $4.99  
BUY

Used only when you want to attach your SmartFence directly to a table top rather than to our Clincher. The brackets lock into extruded T-slots on the back of the fence and grab the sides of your table top. There are two sizes to accommodate table tops of varying thicknesses.
SF-MB0  (for 3/4" thick Phenolic tops)    $11.95     $9.99   BUY
SF-MB1  (for tops 1" to 1-1/4" thick)       $12.95    $10.99   BUY
SF-MB2  (for tops 1-1/4" to 1-5/8" thick)  $13.95    $11.99   BUY

The Jointech Routing Template will allow you to cut an opening into your router table to accommodate any of Jointech's Router Plate Inserts. Finished size is 9-1/4" x 11-3/4" opening. Easy to use Routing Template is made of 3/4" MDF. Complete with instructions on how to rout your own router plate opening.