Technical Support  |   Comments & Suggestions  |    Customer Service    



 

~SawTrain Brochure

Saw Train’s innovative design allows you to customize your table saw setup with 1 or 2 extension tables and 1, 2 or even 3 router workstations. By simply releasing one clamping knob on the sliding bridge assembly, the fence can be moved over the entire length of the rails to increase rip capacity.

The setup can be quickly disengaged from the rails, lifted straight up off table for removal or reversed for use from back side of saw. Included rail stop and 48” scale may be used to accurately extend rip capacity up to 48". Saw Train’s 5-point locking system guarantees that when you move it, remove it, reverse it or repeat it, the fence will always remain parallel to the saw blade. This is a feature that no other fence can achieve, regardless of cost.

The sliding bridge allows Clincher and SmartFence to be repositioned anywhere along the length of your SawTrain rails. That means you don’t need an oversized positioner to achieve maximum rip capacity. Our JCM-1832, which includes an 18” Clincher, can easily make a 48” rip cut assuming your rails are long enough. The sliding bridge can easily be removed and mounted on the rails from the backside of the saw. This can come in handy when routing large panels. By working from the backside, you will not have to lean over the saw table and you will be able to walk around the edge providing more leverage on your workpiece.


  


  Routing Using SawTrain System
Bringing SawTrain to your table saw gives you the most accurate table saw fence on the market, but it doesn’t end there. By mounting your router to the extension table, you can now use the same fence for all your routing. Raised Panel doors, molding, chamfering, and any other edge forming operation is easily accomplished with our award-winning fence. You will also be able to joint the edge of any board just by using a straight bit. Also, using the Jointech templates, any type of joint is possible as well. No need for a stand alone router table. Now you can make dovetails, sliding dovetails, double dovetails, through dovetails, box joints, double-double box joints, and the list goes on... accomplished all on your table saw!

Removing SawTrain Bridge
By unclamping the lock knob on the front clamp, SawTrain bridge can easily and quickly be removed from the table saw at any point along the length of the rails. Lifting up on the bridge and disengaging the back clamp from the rear rail allows you to remove the bridge and mounted fence system as one unit. This makes it convenient when you want the extra work space on top of your table saw.


SawTrain Reposition Scale
All SawTrain Systems include a 48” Scale that fits into the rail system. This durable scale is 3/4” wide providing easy viewing. Scale use is intended for repositioning of the SawTrain bridge to establish greater rip capacity. For example, using the 18” Clincher will allow you to set the fence up to 18” away from the Saw Blade. If you needed to make a 25” cut, it can easily be accomplished by using the SawTrain Scale. Once you have zeroed the moveable scale, then the Sliding Bridge can be repositioned back 7” to achieve the 25” rip.

SawTrain Bridge Stop
The bridge stop serves a couple of uses. It keeps the sliding bridge from falling off the end of the rails by making contact with the bridge clamp. Also it can be used as a reference marker. If you have to move the sliding bridge to another position on the rails, you can set the bridge stop up against the bridge clamp prior to making the adjustment. This will allow you to set the bridge back to it’s original position when you are ready.



Saw Train Retrofit Kits

Saw Train Retrofit Kits Include:
1) Two Replacement Rails, 48", 56", 72", 76" or 96"
    packaged with extension table mounting brackets & fasteners.
2) Sliding Bridge Assembly, completely assembled.
3) Fence Clamping Brackets, completely assembled.
4) All hardware required & instructions.
PLEASE NOTE:
If you already own a Jointech Fence Positioning Machine (IPM or Clincher) and a 32" SmartFence, then all you need is a Saw Train Retrofit Kit to attach to your table saw. If you do not own any Jointech equipment and want a Saw Train Setup - Complete Saw Train Systems can be purchased.
ITEM  DESCRIPTION Price SALE BUY ONE
JST-48 48" Saw Train Retrofit Kit 209.00 179.99 BUY NOW
JST-56 56" Saw Train Retrofit Kit 229.00 199.99 BUY NOW
JST-72 72" Saw Train Retrofit Kit 239.00 209.99 BUY NOW
JST-76 76" Saw Train Retrofit Kit 249.00 219.99 BUY NOW
JST-96 96" Saw Train Retrofit Kit 269.00 239.99 BUY NOW

 
                   
     BACK TO TOP
          

Jointech Products are manufactured & distributed by:
iTools Company - San Antonio, TX 78238 - (800) 619-1288
Jointech, SmartFence and CabinetMaker's System are registered trademarks of Jointech, Inc.
This page was last updated oFebruary 21, 2010->.
©2010